Home > News > Content
Reflective Stud Installation Precautions And Installation Methods
Nov 21, 2013

Installation steps are as follows: 

1, Placed to install isolation facilities, determine the installation location, to ensure that the installation.

The location is flat, there are telescopic, nip and uneven road, prior to the formation of the road finishing;

2, With a clean brush to clean the installation location, while ensuring the installation position is dry; 

3, Remove apply a proper amount of glue evenly on the spike; 

4, Press the spike firmly in the installation position to ensure that the square to the right, if the amount of glue more, be sure to clean up; 

5, if it is a way with a nail, make sure the hole depth is greater than the nail foot depth 1cm, hole diameter greater than the nail foot diameter 2mm;

6, after installation is completed within two hours to do a visit to ensure that all the spikes are not equipped with anti-installed crooked or pressure crooked;

7, waiting for the installation of glue curing glue 6-8 hours, remove the installation of isolation facilities.

Spike installation is not a complicated matter, but there are many details that need attention. These details

It plays a very important role in ensuring the quality of the spike and its service life. Hope this Installation Notes can give you some help to avoid installation mistakes.

led cats eyes.jpg



Attached: led studs detailed installation method

Spike with nail installation method

First, a number of protective tools road cone, construction diversion card 2 sets, baton, reflective vest one each.

Before departure everyone must wear reflective vest, to the construction site must be placed good construction license and road cone. (Workers must do: not joking, not slapstick, obey the conductor, 6 hours before the road can not drink), Each team with 2-4 safety staff.

Second, the tool hammer, drill (22mm), tape measure, approved knife, small plastic bucket, chalk, generator, Hand drill, mixer.

Third, product Road nail (with nail)

Fourth, auxiliary materials Epoxy A, B, cement

Fifth, the installation steps

solar led road markers .jpg


 (1) First ruler to determine the installation location, 15m installed one, (press

According to the installation of drawings) to ensure that the vertical position in a straight line, while horizontal alignment, installation Distance and design requirements prevail. 

(2) (Install stud with spike) 22mm in diameter Hammer drill, the depth of the hole than the nail pin nail length 10mm. After drilling the hole drilled ash to dry net. 

(3) the ratio of plastic, plastic A and B glue 1: 0.7, and then add 15% -30% of cement for filling Charge (glue is not easy to stir too much at once, enough to stick a person 50-70 Road Spike glue). Colloid to Stir, (electric drill with mixer) the same color. Each spike tacking requires 40-50 grams About glue. 

(4) the location of the installation site to clean the road, with about 40-50 grams of approved knife plastic

, Into the hole drilled and the location of the required installation of the spike, the spike put up, with pressure Turn left and right twice so that the spike and the road are closely bonded. 

(5) After the spike installation, put the spike

Around the overflow of plastic, with a knife scraping clean, and clean the road.

Six, matters needing attention Do not touch the reflector, to avoid glue stick to the reflector, the impact of anti

Light effect! Pavement with water, damp, oil is prohibited to install spikes (easy to fall off). Install for 4 hours

After withdrawing the road cone.

solar markers.jpg

The Shaanxi Yiyuan Traffic Technology Engineering Co.Ltd. 


Tel.png  Tel: +86-29-88270591

Fax.png  Fax: +86-29-88219082

E-mail.png  E-mail: sxyyjt@sx-yyjt.com

QQ.png  QQ: 1829090767

Zip.png  Zip: 710065 

Address.png   Address: No. 5, Production Ro ad, West Thermal Power Plant, West Section Of Hongguang                     Road, Weiyang District , Xi'an,Shaanxi.China       


We're Here to Help

  • Shaanxi Yiyuan Traffic Technology Engineering Co.,Ltd

    Tel: +86-29-88270591

    E-mail: sxyyjt@sx-yyjt.com

    QQ: 1829090767

    Zip: 710065

    Address: No.5, Production Road, West Thermal Power Plant, West Section Of Hongguang Road, Weiyang District, Xi'an, Shaanxi, China

Newsletter

Enter in your email address to receive deals
and coupons.
Bookmark us today!